Differences

This shows you the differences between two versions of the page.

--- 5_25_floppy_drives:ye_data_yd-380b [2021/04/18 09:01] – js
+++ 5_25_floppy_drives:ye_data_yd-380b [2021/12/14 11:54] (current) – js
@@ Line 3: / Line 3: @@
 ~~NOTOC~~ \\
 ^ Manufacturer    | YE Data |
-^ Model    | YD-380 |
+^ Model    | YD-380B |
 ^ Density    | <abbr>High Density (HD)</abbr>, <abbr>Double Density (DD/2D)</abbr>  |
 ^ Sides    | <abbr>Double Sided (DS/2S)</abbr>, <abbr>Single Sided (SS/1S)</abbr> |
+^ Rotation speed | 300, 360 |
 ^ Maximum seekable tracks   | 84((Modification is required)) / 83 |
-^ Interface | PC-AT |
+^ Interface | Shugart \\ (PC-AT compatible) |
 ^ Data Connnector | 34 position card edge |
 ^ Power Connnector | 4 pin Molex |
@@ Line 13: / Line 14: @@
 ^ Head loading | Mechanical |
 ^ Disk loading | Lever |
+^ Known colors |<WRAP>
+| <colorswatch #EDE9D3: > | Light Beige \\ (PS/2 Beige) |
+</WRAP>|
 </WRAP>
-====== YE Data YD-380 ======
+====== YE Data YD-380B ======
+The YD-380B is a 5.25" double sided high density floppy drive made by YE Data.
+It uses a metal belt to facilitate head movement and locks the disk with a lever. Head loading is done via mechanical linkage.
+It uses the [[#pn128206-01_rev_b|TPN128206-01 Rev. B]] control board and the Sankyo SB68A motor board.
+===== Pictures =====
+| {{:5_25_floppy_drives:ye_data_yd-380b:back1.jpg?200 |}} \\ {{:5_25_floppy_drives:ye_data_yd-380b:back2.jpg?200 |}} \\ {{:5_25_floppy_drives:ye_data_yd-380b:back3.jpg?200 |}}| {{:5_25_floppy_drives:ye_data_yd-380b:top.jpg?200 |}} | {{:5_25_floppy_drives:ye_data_yd-380b:bottom.jpg?200 |}} |
+| {{:5_25_floppy_drives:ye_data_yd-380b:front.jpg?200 |}} | ::: | ::: |
+===== Jumper settings =====
+==== PN128206-01 Rev. B ====
+{{ :5_25_floppy_drives:ye_data_yd-380b:pn128206-01_revb.pdf |}}
+++++View PDF|
+{{pdfjs 100%,800px>:5_25_floppy_drives:ye_data_yd-380b:pn128206-01_revb.pdf?page-width}}
+++++
+===== 84 track seeking =====
+Unmodified drives will not be able to seek 84 tracks. A major modification is required to enable this.
+{{:5_25_floppy_drives:ye_data_yd-380b:mod_84tracks_1.jpg?200|}}
+{{:5_25_floppy_drives:ye_data_yd-380b:mod_84tracks_2.jpg?200|}}
+The modification can be performed by following these steps:
+  - Mark the current position of the stepper motor in relation to the drive body.
+  - Unscrew the stepper motor.
+  - Unscrew the springs that hold down the guide rod of the head assembly on the stepper motor side.
+  - Move the head assembly and guide rod out of the way.
+  - Use a rotary tool to grind down the head assembly end stop as pictured.
+  - Clean the drive of any metal dust.
+  - Put the head assembly and guide rod back in place.
+  - Screw down the springs that hold down the guide rod of the head assembly on the stepper motor side.
+  - Screw down the stepper motor so that it can still be moved with some friction.
+  - Reposition the stepper motor in relation to the drive body using the marks done earlier.
+  - Screw down the stepper motor all the way.
+  - If the positioning isn't done right the tracks have to be re-aligned.